• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat van Key Replacement 500 Key Fob Won't Work

A key fob for the fiat remote key 500 makes it simple to open doors and start your vehicle. There are a myriad of reasons why the fob may stop working. This includes a dead battery water damage, receiver modules issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't work is a dead battery. Modern key fobs only have only a limited range of operation and must be within a few inches of the vehicle to function. If you are far from your vehicle and you press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) with a fresh one from a reputable brand such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.

After you've replaced the coin cell battery, you can test it by standing in front of your fiat car keys cut 500 and pressing the buttons. The car should flash its parking lights, and the key fob should operate the lock and unlock buttons.

If the fob's remote doesn't function after replacing the battery, it may be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can occur through a variety of methods, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a bag of rice to draw out the moisture. If this isn't working, you'll need to have your fob changed by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually die. Getting the fob wet is not an option however, if you drop it into a cup of water or do not remember to remove it from your pocket before you run the washer Don't give up hope.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Test the fob afterward to verify if it's functioning. If the key does not work, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If your key is older and has not been programmed to work with your vehicle then you'll need to replace it completely. This is a simple procedure that can be completed by a professional locksmith for automotive use. The locksmith will need the key to be cut to match your car's ignition. The locksmith also needs to reprogram your fob into the vehicle's system. This is an affordable and quick procedure that can be completed within the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob could stop functioning is because it's out of range. The remote has a range of 30 feet. So should you be too far from your car it won't be able to respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If you've replaced the battery in your coin (commonly called a "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. Reprogramming the fob usually resolves this problem. You can find the instructions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.

It is possible to replace the metal clips that keep the battery of your coin in place. If they become loose, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob might be out of connection with your vehicle as a result due to hardware or software issues. This can cause a major problem, but you can often fix this by visiting an auto locksmith to reprogram your fob. In certain instances the software may require reinstallation in your body control modules.

Interference

In addition to a dead coin battery The key fob may not be able to transmit or receive a signal due to interference. This may happen if the key code fiat fob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob might not function because of a weak connection with the buttons water damage or damage to the internal chips.

If the key fob suddenly stopped working, out of the blue or even after trying everything you can do at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the onboard systems in your 500, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers, which could help get your key fob working again. If the issue persists you should speak with an expert technician. They will be able to determine the exact cause of your issues.