• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Door Hinge a Loose Door Hinge

The majority of homeowners can fix hinges that are loose. If, however, the holes for screws are smashed and aren't able to hold screws, you may need to use wood glue and dowels before you can install the hinge.

Clean up any surface corrosion. This will help keep the dowels in their place and provide a solid foundation to hold onto.

Remove the Hinges

Most hinges for upvc doors on doors can be removed, which makes it easier to move the door from one side to another or take the entire door off of the frame should it be needed. Anyone who is patient can remove the hinges, however, you must know what to do.

If the hinges have been painted it is necessary to remove it prior to trying to remove the pins. It is possible to scratch your door if you do not remove the paint. Put the hinges in an stainless steel pot and fill it with water until the hinges are completely submerged. Let the hinges rest in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to get rid of the pins.

Once the pins have been loose, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, however it is recommended to use a magnetic screwdriver for this job. This type of screwdriver is specifically designed to take out metal screws and will aid you in getting the job completed much quicker.

Before you attempt to remove the hinges it is a good idea to spray them with some grease. A simple lubricant can make the process to go more quickly and aid in the removal of the screws and pins. You can purchase this kind of lubricant at most hardware and home improvement stores.

It is important to keep in mind that the number of hinges you'll require will vary based on the kind of door and its settings. Heavy doors and solid-core doors will require more hinges while hollow-core doors that weigh less might only require two or three.

It is also important to understand the different types of hinges in order to determine which ones will work best in your situation. Exterior hinges are designed to hold the weight of a patio door hinges, while hinges for interior use must be able to support heavier loads.

Reattaching the Hinges

Sometimes a door hinge will loosen over time and start to hang in a crooked manner or sag. This can cause problems but is usually easy to solve. Retightening the screw will typically resolve the issue. However, if the screw holes are ripped out, it can be more difficult to do. A wood dowel can be used to tighten these holes once more.

Begin by drilling out the hole you had previously made using the drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a tight fit, the dowel should be cut at the same length as the screw. Then, reinstall the screw and tighten it to the desired tightness. If the door continues to bind up, you can insert another dowel into the gap. Repeat the procedure. Close the door slowly after each adjustment to make sure that the perimeter clearances are correct.

Another option is to just utilize the wood plug instead of dowel. It will work just as well but might take a little longer to set up. Simply whittle a chunk of wood to the proper size to ensure a secure fit, then tap it into the hole. If you don't have a woodworking tool you could also make use of toothpicks or wooden matches.

Make use of a countersink to make the hole smaller than the head of screw after you have installed it. This will stop the screw from hitting the edge of the doors when they are closed and opened. This will make it much easier to tighten the screws after replacing hinges.

After installing the hinge, make sure to lubricate the hinge using an oil-based lubricant that is dry. This will prevent it from becoming stuck in the future. Products like PB Blaster or Liquid Wrench are great options. Apply a thin coating and allow it to penetrate the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're not yet ready to replace your hinges, you can try a few simple fixes. Check that the screws that hold the hinge plate to both the door frame and the frame are in good condition. If they're loose, tighten them with a screwdriver or power drill. Be careful not too tighten the screws as this could create gaps at the trim joints, or worse, strip the threads.

If the problem is the hinge plates are breaking they can be reattached to the plates by putting wood glue on the back of them and then inserting wooden dowels or toothpicks into the holes. The toothpicks and dowels provide an solid foundation for the screws, preventing the plates from shifting as you insert them. Allow the glue to dry before attaching the hinge.

The screws can also be stripped or missing. This issue can be resolved by replacing the screws. Make sure you use a drill bit that matches the size of the screw hole to avoid drilling into other parts of the hinge or jamb.

After you've reattached your window hinge repair cost, close the door and examine the gap between the frame and the door. The gap should be the thickness of a penny or less if the old door was hung incorrectly. This should not be a problem if the hinges are correctly installed.

If you discover that the hinges are still loose, try putting the thicker shim of the hinge between the hinge plate and the mounting surface, to create an extra inch of space. You can also take off the hinge pin and then pound it down with a heavy hammer to tighten it up or choose an entirely new hinge. You can also lubricate your hinges with mineral oil or jojoba to reduce friction and hold them in their place. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

A hinge's continuous movement causes friction, which attracts dust particles. Without periodic cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and build up over time. In the end the hinge can become stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication and inspections will maintain the integrity and functionality of hinges on doors.

Check the hinges for the accumulation of rust. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace them. If you are able to save the hinges, remove any loose rust by using steel wool and wire brush. Apply a commercial rust-removing product or a homemade solution such as lemon juice on the hinge. Let the rust remover sit on the hinge for several minutes to dissolve and penetrate any remaining corrosion.

If you don't want to spend money and time replacing your hinges, simply retightening the screws can make the hinges functional again. It might be necessary, however, to add an shim of wood or a dowel to the hinge when the screws have been stripped. Dowels made of wood are square pieces made of wood in the shape of rods which are available in different lengths and sizes. They can be purchased online, at woodworking supply stores and at home improvement stores.

You can also create an shim using metal or plastic depending on the type hinge you own. To make a dowel cut a piece of wooden dowel or another sturdy material to the size you want. You can then dip a dowel into carpenter's adhesive and then insert it into the hole. The glue will secure the dowel in the position.

Before cleaning the hinges, put down a towel or cloth to protect your flooring from spills. After the area has been secured then clean the hinges with an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to eliminate built-up dirt, grime and tarnish. You can use a toothbrush or small brush to reach difficult-to-reach places in tight spaces and crevices.