• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge - simply click for source - a Loose Door Hinge

Fixing a loose door hinge can be a doable job for most homeowners. If the holes for screws are shattered and do not hold screws, you might need to use dowels and wood glue in order to reinstall the door hinge.

Before you do that, however you should clean off any the surface rust. This will help to keep the dowels in their place and provide a solid base for them to rest on.

Removal of the Hinges

Most hinges on doors are removable, which makes it easier to move the door from one side to another or take the entire door off the frame, if needed. The removal of the hinges is easy for anyone with a bit of patience, although you need to know how to do it right.

If the hinges have been painted, you'll need to remove it before you attempt to remove the pins. You may scratch your door if you don't take off the paint. To break the seal of the paint put the hinges in an stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

After the pins have been removed, take the hinges and frame from the door hinge repair. You can make use of a screwdriver to get the job done, but it is recommended to make use of a magnetic screwdriver for this task. This type of screwdriver has been specially designed to pick up metal screws and will aid you in getting the job accomplished much faster.

Before you attempt to remove the hinges it is recommended to spray them with a lubricant. A simple lubricant will allow you to move the process along faster and make the removal of pins and screws more easily. You can find this type of lubricant at most hardware and home improvement stores.

The number of hinges for upvc doors needed will also depend on what type of door you have, and how it is set up. Doors with a heavier core and solid-core will require more hinges while hollow-core doors with a lighter weight may only require two or three hinges.

Understanding the different kinds of hinges can help you decide which one is the best for your situation. The hinges on the exterior are designed to support the weight of the door and interior hinges have to be able to handle lighter loads.

Reattaching the Hinges

Over time, a door hinge can lose its grip and then begin to slide or hang crookedly. This could be a problem, but it's usually easy to solve. In most cases an easy tightening of the screw will solve the issue. However when the screw holes are stripped out, it can be more difficult. A wood dowel could be used to tighten these holes again.

Begin by drilling out the hole from the previous one using a drill bit that is close to the size of the new screw (typically 3/8"). Then use wood glue and a dowel made of wood to fill in the hole. The dowel should be cut to a length that is the same as the screw to ensure a snug fit. Reinstall the screw and tighten it to the desired level of tightness. If the door continues to bind up, add another dowel to the gap. Repeat the procedure. Close the door slowly after each adjustment to make sure that the perimeter clearances are in order.

You can also use a wooden plug instead of the dowel. This will work as well however it may take a bit longer to install. Simply whittle a chunk of wood to the right size for a snug fit, then tap it into the hole. If you don't have a woodworking instrument You can use toothpicks or matchsticks made of wood.

After you've reinstalled your new screw, use a countersink bit to make the hole for the head of the screw smaller so that it won't touch the edge of the door when it is opened and closed. This will allow you to tighten the screw after reinstalling the hinge.

After installing the hinge again, you should apply lubrication to the hinge using a dry lubricant. This will help to prevent it from becoming stuck in the future. Products such as PB Blaster or Liquid Wrench are great options. You should apply a light coat and wait for approximately 15 minutes to reach the hinge barrel.

Refinishing the Hinges

If you're not sure if you're ready to replace upvc window hinge the hinges on your door, you are able to do a few simple repairs. Verify that the screws that secure the hinge plate to the door frame and frame are in good condition. If they are loose, tighten them with a power drill or screwdriver. Be careful not to over tighten the screws, because this could cause gaps to appear at the trim joints, or worse, strip the threads.

If you're experiencing issues because the hinge plates are separating from the door and jamb, you can reattach the hinges by applying wood glue to the back of the plates, and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will serve as a solid base for the screws and prevent the plates from shifting when you drive them into position. Allow the glue to dry before reattaching the hinge.

Another reason for hinges that are loose is that screws are worn out or missing. This issue can be resolved by replacing the screws. Use a drill bit that is exactly the same size as the screw hole to avoid drilling into the jamb or hinge.

After you've reattached your hinge close the door and examine the gap between the frame and the door. It should be approximately the thickness of a nickel all the way around, or less if there's a gap that was caused by a previous door that was not properly hung. This shouldn't be a problem if hinges are installed correctly.

If the hinges are still loose, you can add a thicker hinge between the hinge plate surface and the mounting surface. This will give the hinges a little more room. You can also take off the hinge pin, then pound it down with a powerful hammer to tighten it or use a new hinge. You can also lubricate the hinges with mineral or jojoba oil to decrease friction and aid in holding their position. Lubricating your hinges regularly can stop them from becoming stiff and squeaky and also prolong their lifespan.

Cleaning the Hinges

The friction created by the constant movement of a hinge attracts dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges if they are not regularly cleaned and lubricated. In the end, the hinge becomes stiff and creaky and its appearance could get worse. Regular cleaning, lubrication and inspections will maintain the integrity and functionality of hinges that are attached to doors.

Check the hinges for corrosion. If the corrosion has reached the point of destroying surface of the barrel or screw holes, you'll require replacement of the hinges. If you can save the hinges, first brush away loose rust using steel wool and a wire brush. Then apply a commercial rust remover or homemade solution like lemon juice on the hinge. Let the rust remover sit on the hinge for a few minutes to dissolve and penetrate any remaining rust.

If you don't want to spend cost and time to replace your hinges, simply retightening the screws will restore the hinges' functionality. If you have stripped the screws however, it could be necessary to attach the dowel of wood or shim to the hinge. Wooden dowels are round pieces of wood that are in the form of rods which are available in varying lengths and sizes. You can purchase them on the internet, at woodworking supply shops and home improvement centers.

A shim can be made of a piece of plastic or metal, based on the type of hinge you have. To make a dowel cut a wooden dowel to the desired length. You can dip the dowel into the adhesive of a carpenter and insert it in the hole. The glue will secure the dowel in the position.

Before cleaning the hinges, lay down a paper cloth or towel to shield your flooring from spills. After the area has been secured, proceed to clean the hinges using a soft cloth or sponge that has been soaked in mild cleaner or vinegar to get rid of dirt, grime, and tarnish. You can make use of a small or toothbrush brush to reach hard-to-reach spots in crevices or tight areas.