• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons to Change Door Lock

You can change the lock on your door for a variety of reasons, from increasing the security of your home to redecorating the entryway. You may need to change locks if your key gets stuck or is difficult to turn.

Changing your lock is a simple project that even beginner DIY homeowners can take on. Get the tools you need to begin.

Remove the old lock

Before installing a new lock, it is necessary to remove the old one from the door. This is important when you suspect that someone else may have a key to the home. This is also a good idea following you've moved into a new house, had a break-in, or welcomed a roommate. It's much simpler than you think to complete and can be done in a matter of minutes.

Start by removing the screws that secure the deadbolt faceplate onto the frame of the door. You'll need to remove the screws on both sides of the door to remove the faceplate. This will let you discover what's behind it and will give you a better idea of how to proceed with the remaining steps.

After removing the faceplate you will have to remove the bolt along with the strike plate and strike plate. Use a screwdriver to loosen the bolt, and then remove it from the hole in the door. If the bolt is rusted you may need to use a chisel or hammer it. If you use a chisel to remove the bolt, be careful not to scratch the door frame.

Make sure your new doorknob, deadbolt and lock will fit into the existing holes in the door before you remove the old one. Numerous hardware stores and large box stores have a wide selection of locks and can assist you in selecting the best one. Get help if the lock you purchased doesn't fit your door.

While you're taking off the old lock, search for small slits or depressions in the handle or around the trim. If you can find them, slide a straightened safety pin or a flat screwdriver into these to open the handle and expose screws underneath.

After the screw in the handle has been removed you can now begin to remove the knob from its spindle. To do this, find the set screw at the base of knob and loosen it. The next step is to remove the knob from the spindle. Finally, carefully remove the spindle from the door.

Install the new lock

It's a good idea to change locks on doors throughout your home regularly, especially after a burglary or when you move in with roommates. It's an affordable, simple and effective method to ensure that your home is secure. The majority of people can do this yourself with a screwdriver and some basic instructions. Depending on the circumstances you may be interested in learning how to reset a lock to ensure that you only have the key.

To begin the process, you have to purchase a new lock that is compatible with your existing lock's keyway. Many locksmiths will replace your lock at an additional cost however, you can save money by doing this yourself. You can buy an entirely new lock from hardware stores or on the internet. Standard deadbolts will fit most doors. However, you'll have to measure the door to ensure it is suitable.

Your new lock will often come with a diagram that will show how to put it on the door. The template can be used to drill the hole. It is much easier than having to measure each time. If the template doesn't line to your hole then you should return it to the hardware store to purchase an alternative.

You must install the new lock on the right side of the door. You can check this by looking at the latch, which must be labeled "up" or something similar. Make sure that the latch is correctly seated on the plate and then attach it using the supplied screws.

When replacing a knob lock, you should also be aware of its handing. Certain knob locks are right-handed. If you are not careful, the knob could be installed on the wrong side of your door, which could make it impossible to lock from the inside or outside.

After you're done checking the new lock to make sure it functions. You should be able to lock and unlock the door with keys from the inside as well as from the outside. If you are not satisfied with the result, you can contact an expert locksmith to repair it.

Test the lock

A door lock that will not unlock can be annoying but it can also put your family's safety at risk. It's easy to solve the majority of door double glazed window lock repairs issues by conducting some troubleshooting and lubrication. To start with, check whether your key has been properly cut and that the lock isn't soiled or loose. If this doesn't resolve the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based grease.

Make sure that the doorlock switch, wiring harnesses and actuator connectors all function properly. Consult the wiring diagram or manual to determine the color-coding and function of each wire of the door lock switch. Then, use a test light or digital meter to see if the door lock actuator receives power and ground when the switches are turned on. If you see an electrical voltage switch with every switch activation, this means the switches are working and it's likely the actuator that requires to be replaced.

If the switch seems to be working but the actuator does not move when you turn it, there may be a problem with the cylinder. The actuator cylinder is outfitted with pins that are spring loaded. They prevent the cylinder from turning until the key is inserted which then pushes them up to match the height of the key at the location. The cylinder will then begin to rotate, opening the lock body and allowing the latch to open for the handle.

If the door lock actuator still not functioning, you can remove it by using a small screwdriver. You will need to loosen the bolt that locks it first and then separate the plastic cover that holds the electrical connector. Then you must disconnect the door actuator from the double glazed window lock repairs near me and let it fall. Then, you should be able find the two bolts of 10mm that keep the actuator in place, and remove them. Once the actuator is removed, you will be capable of disconnecting the black electrical connector and then pull it out along with the actuator and lock assembly.

Replace the key

If your deadbolt is locked or door knob isn't working, you will need to rekey it or replace it. It's not too difficult and will save you money. But, prior to doing this it is recommended to have a locksmith look over the locks and check them for any issues. This will give peace of peace of mind knowing that your home is secure and safe.

To begin, take off the faceplate on the outside from the doorknob or deadbolt. If there are screws that hold the faceplate in place then use a screwdriver to pull it off. Next, use a flat head screwdriver to remove the interior faceplate. After you have removed the faceplate, you are able to remove the bolt and screw from inside the lock cylinder.

A locksmith can determine if you need to replace or rekey your lock. They can also give you advice on the best security measures for your home. They will also make any necessary modifications to the door Window And door lock repair frame to ensure a perfect fit. They will also provide the guarantee for their work.

If you decide to rekey your lock, you must first purchase an additional key for it. It is crucial to select a upvc window lock replacement key that is snugly fitted. A key that's not the right size may damage the internal mechanism of the lock and stop it from working. Insert the key into the lock to check its size. If it is flush with the plug, it's of the correct size. If the pins stick out from the top of the plug, they're too long.

There are many reasons why you might want to change your door lock, including:

Rekeying a lock is a cheaper option than replacing it if you are moving into the home of a previous owner or if your keys are missing. It's also less costly than a full replacement. However, there are instances where rekeying an existing lock isn't an option. If the lock has been damaged or repeatedly jammed, as in it could be the right time to replace it.